CONTINENTAL Valve Cover Gasket - FITS IO-550; GTSIO-520 + # RG-632459 Silicone

Description: VALVE COVER GASKETS - SILICONE forCONTINENTAL - GTSIO / TSIO-520's and IO / IOF / TSIO / TSIOF-550's - see specific list below - Our silicone rubber gaskets are made from aerospace mechanical grade AMS silicone and designed to withstand temperatures up to 400 degrees Fahrenheit. - Therefore, they will not break down and deform or crack up like cork or neoprene. - Our gaskets seal uneven and warped surfaces, and eliminate corrosion. - Gaskets are 100% reusable. FAA-PMA approved for the following engines.Fits: Continental engines GTSIO-520-C,-D,-F,-H,-K,-L,-M,-N; TSIO-520-BE; IO-550-G,-N,-P,-R; IOF-550-N,-P,-R; TSIO-550-A,-B,-C,-E,-G,-K,-N Series; TSIOF-550-D,-J,-K,-P Series Part #: RG-632459SUPERSEDED NUMBERS: 658735, 655705, 653380, 653168, 649993, 632459Price is per gasket.Silicone gasket has 5 bolt holes and is 1/8″ thick.A complete set is 12 gaskets.Reusable. INSTALLATION AND MAINTENANCE PROCEDURES:THE GASKET SURFACES MUST BE CLEAN AND DRY. 1. Remove the valve cover and gasket in accordance with the Continental procedure or in accordance with an acceptable procedure used by the shop performing the installation.2. Clean the valve cover and the cylinder surfaces of all residual material. 3. Install gaskets, DRY, 4. Replace the valve cover and torque the cover bolts to 25 in-lbs. "CAUTION" - DO NOT OVER TIGHTEN. Over tightening makes the gasket bulge or squeeze out. 5. Check the cover bolt torque after an engine run up to take off power or first flight and re-torque the bolts to 20 in-lbs. 6. Check the cover bolt torque annually, and re-torque to 20 in-lbs, if necessary. The gaskets are re-usable and the service life of the gasket is determined by its physical condition on removal. If the gasket is still pliable and without cracks, tears, or deterioration, it may be re-used, otherwise discard. TO REUSE GASKETS: Wash briefly in hot soapy water. Rinse well and dry all surfaces. Re-install using the above installation instructions. Save instructions for future reference. Instructions do come with the gaskets. PROUDLY MADE IN THE USA.~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ USE CORK? GET REAL! REAL Gaskets that is…REAL Gaskets Tennessee is a manufacturer of silicone rubber gaskets for aircraft, automobile, and motorcycle engines.Our silicone rubber gaskets are made from aerospace mechanical grade AMS silicone, designed to withstand temperatures up to 400 degrees Fahrenheit and to last the life of the engine. Our gaskets seal uneven surfaces, eliminate corrosion and are 100% reusable. We manufacture valve cover gaskets for: Aircraft: Continental, Franklin, Lycoming, Pratt & Whitney and Wright radial piston aircraft engines. Automobiles: Chevrolet, Ford, GM, Mopar, Porsche and VW automobile engines. Featuring NEW *ULTIMATE* GASKETS that are fiberglass reinforced silicone. Check them out! Motorcycles: BMW, Harley-Davidson, Suzuki, BSA, Ducati, Moto Guzzi, Norton, Triumph, Saab and most other motorcycle engines. If you are tired of oil leaks, then a silicone rubber gasket is the only way to go, and REAL Gaskets Tennessee is the only place you can get “The Original” silicone rubber gasket. MADE IN THE USA.

Price: 6 USD

Location: Elizabethton, Tennessee

End Time: 2024-08-27T20:23:53.000Z

Shipping Cost: 11.95 USD