MOSKY ACCURATE DRIVE Guitar Bass Effect Pedal Overdrive Noise Gate 4 Mode Bypass

Description: MOSKY ACCURATE DRIVE Guitar Bass Effect Pedal Overdrive Noise Gate 4 Mode Bypass MOSKYaudio ACCURATE DRIVE Guitar Bass Effect Pedal Overdrive Noise Gate and Four Models With True BypassACCURATE DRIVEBased on HORIZEN DEVICES PRECISION DRIVE ( but with many more options)Never worry about fighting your tone or your gear again with the Accurate Drive, the first modernoverdrive made by guitar players for guitar players. The Accurate Drive can take any set-up,both tube and digital, and turn it into the perfect modern metal rig with its precise tonal carving controls.Crafted with a bright knob instead of tone for retaining clear singing tone, an attack control to tailor the pedal to your rig,and a built-in noise gate for retaining shape and punch at higher gain, the Accurate Drive rethinks the overdrive with new controlsfor a pedal that brings your sound to new heights. Taking a novel approach to dirt boxes, the Accurate Drive sets itself apart for theminute adjustments available to make the pedal adapt to and complement your rig without sacrificing grit.A workbench of tone-sculpting tools in one box.PEDAL PLACEMENT:Place the Precision drive before your amp (or pre-amp, if you are not using a traditional guitar amp), not in the FX loop.SIGNAL SETUP:As mentioned above, in order for the tonal benefits of an overdrive to work properly, it must be placed before yourpreamp (where the core of your tone is generated). When using a normal amp, this means that you should run the pedal in front,not in the FX loop. If you are using the Accurate Drive in front of a preamp/distortion pedal, like the 5150OD, make surethe Accurate Drive is before that pedal in the chain. The same logic applies to modeling units or plugins. Just make sure theAccurate Drive is before the amp block or the plugin when routing! The Accurate Drive will always work fine in front, but different unitshandle pedals (especially drive pedals) in their loops differently. Make sure you set your levels cleanly and properly to avoid noise issues.AMP SETTINGS:For distorted tones, you can feel free to dial in very thick and undefined tones, then clean them up with the Accurate Drive.You could also keep your amp’s settings on the dry side, and then shape that tone with the Accurate Drive.For cleans, you can set that channel up to taste, and use the Accurate Drive to dial in more mids and crunch, almost acting likea second channel. There really are no rules, though, I’m sure you will come up with way cooler ideas!VOLUME:6 on the Accurate Drive is roughly equal to 10 on a Tubescreamer. So starting the volume at noon is usually a good bet.Adjust to taste from there.BRIGHT:We made sure this control could be very bright in order to help make dark or muddy amps cut. So be careful when using the pedalfor mid/low gain tones, because it can be a bit harsh in the upper portion of its range. When doing this, don’t be afraid toturn this knob pretty far to the left. It will tame it right up!ATTACK-4 MODE:Towards the left is more of a lower mids punch, and to the right can get very defined and pick-y. Left is a little more oldschool and thick,right is very modern and clear. You can get tons of unique combinations combining the attack knob with the bright knob. Turning brightup as you turn attack to the left can help keep your sound balanced, and vice versa. Or totally double down with both to the left for doom-y tones,or both to the right for super bright and cutting tones.DRIVE:You’re going to want to start with this near zero at first, as with most pedals. A cool trick is to dial in a really dry and clear tone, then slowly turnthe drive knob up to around 1-2 until you get the level of saturation and thickness you’d like. We put a lot of effort into this portion of the circuitto make it actually usable, so feel free to turn it up for mid-gain tones, or to add saturation and sustain to your solos.GATE:Towards the left, the gate will eliminate most noise, with minimal tonal effect. To the right, you will get very tight bass response, but it will begin tointerfere with your soloing a bit. Noon is a good middle ground that will work for most players and their applications. Like any gate, as you use yourgain, your sound becomes less tight. However, please take note that using a lot of gain (tons of amp gain, tons of pedal gain, tons of both) can simplyoverload the gate and keep it from working properly. No one wants to be that guy with screeching undefined tone, so using the proper amount of gainis always a good call!SPECIFICATION:True Bypass SwitchingAC Adapter (Optional): 9VDCNegative Tips (Regulated recommended)Dimension(L*W*H):11.5*6.5*5CMWeight:320g Note: Power supply not included. Please use a 9V DC power adapter whose polarity is negative center otherwise, the product may not work properly. Package List: 1 * Effect Pedal 1 * User Manual(English ) 1 * Year warranty through our store No Duty to Canada and USA FAST 'N FREE USA Shipping (typically about 5 days)Ships from Canada *Just to be clear on DUTY, (regardless of what Ebay warns buyers of ) Canada and the USA have a trade agreement in place that allows US citizens to purchase/import up to $800 dollars per purchase in to the United States from Canada with NO Duty at all, State taxes are another story, some states charge a TAX some do not, BUT NO duty. \

Price: 39.8 USD

Location: Brantford, Ontario

End Time: 2024-09-11T00:21:36.000Z

Shipping Cost: 0 USD