NEW HPI G3.0 Stadium Truck Engine Nitro Slide Carb w /Pull Start 101310

Description: NEW HPI G3.0 Stadium Truck Engine Nitro Slide Carb w /Pull Start 101310 HPI Racing 101310 Nitro Slide Carb w /Pull Start G3.0 Stadium Truck EngineThis is the Nitro Star G3.0 Engine with Pullstarter supplied with theHPI Bullet ST 3.0 Monster Truck and Bullet ST 3.0 Stadium Truck.FEATURESABC liner construction, "A"luminum piston with "B"rass cylinderliner that is "C"hrome platedTwo needle composite body slide valve carburetorSG type (integrated pilot shaft) crankshaftTwo year limited warranty through HPI beginning at date of purchaseINCLUDESNitro Star G3.0 Engine with Pullstarter, Air Filter Assembly, GlowPlug, and InstructionsREQUIREMENTSGlow Fuel: Car blend nitromethane with 20-25% nitro contentGlow starter, air filter oil and track equipmentSPECIFICATIONSDisplacement: .18 cu in (3.0 cc)Output not provided by manufacturerDistance between Mounting Holes Same Side: 0.47" (12mm)Distance between Mounting Holes Opposite Side: 1.2" (31.5mm)Height from Mounting Tab/top of Cylinder Head: 3" (76mm)Height from Bottom of Crankcase/top of Cylinder Head: 3.5" (89mm)Width of Mounting Tabs: 1.6" (40mm)Length from Pull Starter to Front Bearing: 3" (75.5mm)Length from Back Plate to Front Bearing: 2.2" (55.5mm)Length from Pull Starter to end of Crankshaft: 4.2" (107mm)Length from Back Plate to end of Crankshaft: 3.5" (88mm)Carburetor Settings;High Speed Needle: 1/4-3/4 turn clockwise from flush (never turnpast a maximum of 3/4 turn clockwise from flush)Idle Adjustment Screw: Turn counterclockwise to reduce idle speedor clockwise to increase, idle speed should not engage clutch,set throttle trim on radio to neutral before setting idle.Low Speed Needle: Set flush with carb body, let engine idle for 30seconds, then accelerate to 3/4 throttle. If there is a lot ofwhite smoke and slow acceleration the mixture is too rich. If caraccelerates quickly and sputters, the mixture is too lean. Turnneedle in 1/8 turn increments to adjust. Do not turn past 2 turnsfrom flush. NEW HPI G3.0 Stadium Truck Engine Nitro Slide Carb w /Pull Start 101310 HPI Racing 101310 Nitro Slide Carb w /Pull Start G3.0 Stadium Truck Engine This is the Nitro Star G3.0 Engine with Pullstarter supplied with the HPI Bullet ST 3.0 Monster Truck and Bullet ST 3.0 Stadium Truck. FEATURES ABC liner construction, "A"luminum piston with "B"rass cylinder liner that is "C"hrome plated Two needle composite body slide valve carburetor SG type (integrated pilot shaft) crankshaft Two year limited warranty through HPI beginning at date of purchase INCLUDES Nitro Star G3.0 Engine with Pullstarter, Air Filter Assembly, Glow Plug, and Instructions REQUIREMENTS Glow Fuel: Car blend nitromethane with 20-25% nitro content Glow starter, air filter oil and track equipment SPECIFICATIONS Displacement: .18 cu in (3.0 cc) Output not provided by manufacturer Distance between Mounting Holes Same Side: 0.47" (12mm) Distance between Mounting Holes Opposite Side: 1.2" (31.5mm) Height from Mounting Tab/top of Cylinder Head: 3" (76mm) Height from Bottom of Crankcase/top of Cylinder Head: 3.5" (89mm) Width of Mounting Tabs: 1.6" (40mm) Length from Pull Starter to Front Bearing: 3" (75.5mm) Length from Back Plate to Front Bearing: 2.2" (55.5mm) Length from Pull Starter to end of Crankshaft: 4.2" (107mm) Length from Back Plate to end of Crankshaft: 3.5" (88mm) Carburetor Settings; High Speed Needle: 1/4-3/4 turn clockwise from flush (never turn past a maximum of 3/4 turn clockwise from flush) Idle Adjustment Screw: Turn counterclockwise to reduce idle speed or clockwise to increase, idle speed should not engage clutch, set throttle trim on radio to neutral before setting idle. Low Speed Needle: Set flush with carb body, let engine idle for 30 seconds, then accelerate to 3/4 throttle. If there is a lot of white smoke and slow acceleration the mixture is too rich. If car accelerates quickly and sputters, the mixture is too lean. Turn needle in 1/8 turn increments to adjust. Do not turn past 2 turns from flush. × Buy now and save! Shipping info Click the Shipping & Payments tab above the listing description for more info Click the Shipping & Payments tab above the listing description for more info! PAYMENT Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart. Thank you for shopping with us on eBay! Additional Information No additional information at this time Ask seller a question Contact To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist. Ask seller a question © My Store Shipping & Payments Click the Shipping & Payments tab above the listing description for more info Payment Accepted Payment Methods Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart. Thank you for shopping with us on eBay! Returns Returns are accepted Items must be returned within 30 days of the auction ending Seller will pay for return shipping. eBay integration by

Price: 118.79 USD

Location: Mahwah, New Jersey

End Time: 2024-12-05T16:17:17.000Z

Shipping Cost: 0 USD