William Morris Strawberry Thief Red Handmade Lampshade

Description: DESCRIPTION Lampshade using the beautiful William Morris Strawberry Thief Red fabric. This red is a deep lustrous shade with the iconic birds in a linear pattern with shades of gold, green and cream throughout. Slight color variations can occur due to different light and filters in photography. If you are unsure about the fabric and if it will match your interiors, I highly recommend purchasing a fabric sample here: https://www.ebay.com/itm/175759928633 All lampshades have a single seam and rolled edges. Please note that the pattern placement can vary however I try my best to ensure optimal placement each time. The pattern will not always match up at the seam. *Please note that this listing is for the lampshade only, and does not include any other items shown in the photograph. FITTINGS There are several different type of fittings available for your lampshade: 1) Spider Fitting: There is a 1/2 inch recess at the top and fit the traditional lamp which utilizes the harp & finial. If no special note is included in your order, this fitting will be used by standard. 2) Uno Fitting: The uno fitting measures approximately 1 1/4 inch diameter of the center hole and screws around the base of the bulb holder. The fitting is usually on the bottom of the lampshade and has a 2 inch recess so it sits comfortably on the lamp. Please request this fitting in your order, otherwise the spider fitting will be used as standard. 3) Euro Fitting: Similar to the uno fitting, the euro also sits around the base of the bulb holder and is affixed to the bottom of the lampshade with a 2 inch recess. The diameter of the center hole is approximately 1 1/2 inches. Please request this fitting in your order, otherwise the spider fitting will be used as standard. 4) Clip on Fitting: The clip on fitting will affix around the lightbulb and can be used for lamps that do not have a harp & finial or smaller lamps. The sconces and small lampshades can be commonly be fitted with clip on. Clip on fittings come in both Edison (round bulb) and candelabra (torpedo) bulbs. Clip on fittings are available in sizes up to 10 and 12 inch diameters. Please request this fitting in your order, otherwise the spider fitting will be used as standard. LININGS All lampshades have a finishing choice of white, copper, gold or silver lining. All lining used is the highest quality pvc styrene material that is flame retardant and have passed all the relevant safety tests. White lining is the most common and will emit the brightest light through the lampshade. Gold, copper and silver linings will emit decent light but will not actually shine through the lampshade due to the dark nature of the metallic lining. They all emit a warm radiance from the top and bottom and have a decorative feel to them. A low watt or LED bulb is highly recommended. SHAPES & DIMENSIONS All lampshades are offered in the following shapes and sizes: Drum, Empire and Coolie. DRUM Drum lampshades have the same top and bottom diameter and have a very modern and contemporary feel to them. Drums are available in the following dimensions (please check each individual listing as they vary in sizes offered due to fabric width): 6 inches (approx height 6.5 inches)8 inches (approx height 8-8.5 inches)10 inches (approx height 9 inches)12 inches (approx height 9.5 inches)14 inches (approx height 10-10.5 inches)16 inches (approx height 10.5 inches)18 inches (approx height 11 inches) (only certain listings available, please see individual listings) EMPIRE Empire lampshades have a very slight taper and resemble a bell shape. The difference between the top and bottom diameter is only by 2 inches. All the sizes below are measured by top diameter x bottom diameter x height. 6x8x68x10x88x12x1010x12x1010x14x1212x14x1212x16x1214x16x12 COOLIE Coolie or cone lampshades have a small top diameter and a larger bottom diameter to create the ?cone? shape. Again the sizes below are measured by top diameter x bottom diameter x height. *PLEASE BE AWARE THAT THIS SHAPE WILL CAUSE PATTERNED FABRIC NOT TO BE SYMMETRICAL DUE TO THE SHAPE OF THE TEMPLATE. 6x12x88x16x10 SIZING It is the customer's responsibility to make sure that they are purchasing the correct size. Therefore I recommend measuring your lamp base or your existing lampshade for an optimal fit. I also encourage as many questions as you have prior to purchase as it?s essential to get everything correct. Returns and exchanges, although welcome, can be cumbersome as often times sending lampshades back to me means risking damage whereby they cannot be resold to another customer. CUSTOMIZATION If you do not see the size you want above, I can customize any size above to any HEIGHT up to 12 inches for you at NO EXTRA COST. Anything over 12 inches will incur an extra charge. Please either write a note on your order with your specifications or message me. If you require a size that is not offered as standard, please message me directly. TURNAROUND All lampshades are handmade to order with love, detail and care in my workshop. They are not pre-made and ready to ship so please allow at least 3-4 weeks for completion and a further 2 days for dispatch by UPS Ground. RETURNS/EXCHANGES/CANCELLATIONS I do not accept returns on customized orders, only standard size orders, but if you are unhappy for any reason please contact me for resolution. I accept order cancellations within 2 hours of purchase.

Price: 70 USD

Location: Seattle, Washington

End Time: 2024-11-25T21:46:48.000Z

Shipping Cost: 0 USD